Feet & Inches Calculator
Adding and subtracting feet and inches by hand means converting to inches, doing the maths, then converting back — and fractions make it worse. This calculator does it all: add, subtract, multiply and divide lengths in feet, inches and fractions to 1/16.
Enter two lengths (or one length and a number), pick an operation, and get the result in feet and inches, total inches, decimal feet, centimetres and metres.
Result
How It Works
Every length is converted to inches first — feet × 12, plus the inches, plus the fraction — and the operation is done on that single number. The answer is then converted back: divide by 12 for the feet, take the remainder for the inches, and round the leftover fraction to the nearest 1/16 of an inch. For multiplication and division, the second value is a plain number (a multiplier or divisor), not a length — multiplying two lengths would give an area, not a length.
The result is shown in feet and inches (9'4"), and the table gives the same length as total inches, decimal feet, centimetres and metres. One inch is exactly 2.54 cm by definition, so the metric figures are exact conversions of the rounded result, not estimates. A negative answer — from subtracting a bigger length from a smaller one — is shown with a minus sign in front of the whole length: −5'10".
Worked Example
Addition: 5'7" + 3'9" = 67" + 45" = 112" = 9'4". Subtraction: 10'6" − 4'8" = 126" − 56" = 70" = 5'10". Multiplication: 6' × 2 = 72" × 2 = 144" = 12'. Division: 12'6" ÷ 3 = 150" ÷ 3 = 50" = 4'2".
Assumptions
- Fractions round to the nearest 1/16 of an inch. That is the smallest mark on a standard tape measure, so it is the finest fraction you can measure in practice. A result of 4.5 inches shows as 4 1/2".
- Inches may exceed 12. Entering 0 feet and 14 inches is accepted and treated as 14 inches — the calculator normalises it to 1'2" in the result.
- For × and ÷, the second value is a plain number. Multiplying a length by 2 doubles it; dividing by 3 splits it into thirds. Dividing by zero has no answer and shows a clear message.
- Negative results carry one minus sign. −5'10" means 5 feet 10 inches in the negative direction — the minus applies to the whole length, not to the feet alone.
Last reviewed: 15 November 2026.
Built and tested by SumKitTool — see how we check our numbers.
How to Use This Calculator
Enter your lengths, pick an operation, and the result updates live as you type.
- Enter the first length in feet, inches and a fraction (to 1/16).
- Pick an operation — add or subtract a second length, or multiply or divide by a number.
- Read the result in feet and inches, with total inches, decimal feet, centimetres and metres in the table.
The Reset button restores the worked example (5'7" + 3'9" = 9'4").
Tips and Practical Advice
- Work in inches for fiddly sums. The table's total-inches figure is the easiest form to check by hand — 112 inches is 9 feet 4 inches, and you can verify it with one division. Shoe sizes start from a foot length in centimetres or inches — a shoe size converter turns that measurement into US, UK and EU sizes.
- Use the fraction dropdown, not decimals. Typing 0.5 inches works, but picking 1/2 from the dropdown matches how tape measures are marked and avoids rounding surprises.
- For room sizes, pair this with the Square Footage Calculator. Add up your wall lengths here, then work out the floor area there.
- Double-check before you cut. A result rounded to the nearest 1/16 is within a hair of exact — but measure twice, cut once still applies. Stairs are the classic cut-once job — a stair calculator works out the rise and run of each step from the total height.
Frequently Asked Questions
How do you add feet and inches?
Convert both lengths to inches, add them, then convert back: 5'7" is 67 inches and 3'9" is 45 inches, so 67 + 45 = 112 inches = 9'4". This calculator does the conversion for you, including fractions to the nearest 1/16 of an inch.
What is 5 feet 7 inches in centimetres?
170.18 cm. 5'7" is 67 inches, and 1 inch is exactly 2.54 cm, so 67 × 2.54 = 170.18 cm (1.7018 m). The calculator shows the centimetre and metre equivalents of every result.
How do you subtract a bigger length from a smaller one?
The result is negative, shown with a minus sign — 4'8" minus 10'6" is −5'10". The minus applies to the whole length, so −5'10" means 5 feet 10 inches in the negative direction, not 5 feet minus 10 inches.
Why are fractions shown to the nearest 1/16 of an inch?
Because 1/16 of an inch is the smallest mark on a standard tape measure, so it is the finest fraction you can actually measure with one. The calculator rounds the fractional part of the result to the nearest sixteenth — for example, 0.5 of an inch becomes 1/2, and 0.3125 becomes 5/16.
Last updated: